MEAN WELL Products

HomeMEAN WELL ProductsLED Power SupplyPLN-30 Series 30W Single Output UL1310 Class 2 IP64 LED Power Supply

PLN-30 Series - PLN-30 Series 30W Single Output UL1310 Class 2 IP64 LED Power Supply

30W Single Output UL1310 Class 2 IP64 Power Supply

Email
SKU: PLN-30 Series Category:

Description

These limited power sources comply with UL1310 class 2 that under any situation the output power will remain less than 100VA or 5A. This will significantly reduce the hazardous condition exposed to the technicians who execute the construction or maintenance of the LED lighting system. The IP64 enclosure design can protect the electronic components against dust and moisture and makes them suitable for use at indoor or outdoor locations. Thanks to the simplified single stage PFC topology, the required high power factor, as well as the class C harmonic level for the lighting industry, can be achieved economically. Efficiency’s of PLN-30 series are as high as 86% and hence can operate between -30°C ~ +50°C by only free air convection inside the fully covered plastic enclosure. Standard functions include short circuit, over load, over voltage, and over temperature protections. The adjustable output voltage and current level enables the fine tuning of the PSU to comply with the requirement of LED characteristics.

Additional information

Standards

CE

Type

AC/DC,Constant Current,LED Driver

Range Power

Outputs

Single

Input Voltage 90 ~ 264Vac 127 ~ 370Vdc
Input Frequency 47 ~ 63Hz
Power Factor PF>0.9 at 75 ~ 100% load, 115Vac / 230Vac
Input Current 0.4A/115Vac 0.2A/230Vac
Inrush Current 40A/230Vac
Leakage Current 0.5mA/240Vac
Output Voltage Adjustment Range -5% ~ 10%. Can be adjusted by internal potential meter SVR1
Current Adjustment Range 3% ~ -25%. Can be adjusted by internal potential meter SVR2
Output Voltage Tolerance ±10%
Line Regulation ±3.0%
Load Regulation ±5.0%
Set Up Time 1500ms / 230VAC 3000ms / 115VAC at full load
Over Current Protection 100 ~ 110%
Constant current limiting, recovers automatically after fault condition is removed
Short Circuit Protection Hiccup mode, recovers automatically after fault condition is removed
Over Voltage Protection Shut down o/p voltage, re-power on to recover
Over Temperature Protection 95°C ±5°C (TSW1)
Shut down o/p voltage, re-power on to recover
Working Temperature -30°C ~ +50°C (Refer to output load derating curve)
Working Humidity 20 ~ 90% RH non-condensing
Storage Temperature, Humidity -40°C ~ +80°C, 10 ~ 95% RH
Temperature Coefficient ±0.06%/°C (0°C ~ 50°C)
Vibration 10 ~ 500Hz, 2G 12min./1 cycle, period for 72min. each along X,Y, Z axes
Withstand Voltage I/P-O/P:3.75KVAC
Isolation Resistance I/P-O/P:100M Ohms/500VDC 25°C 70%RH
Safety Standards TUV EN61347-1, EN61347-2-13, CAN/CSAC22.2 No. 223-M91(except for 48V), IP64 approved
EMC Compliance to EN55015; EN61000-3-2 Class C (pin25W), Class D (>70% load) ; EN61000-3-3;
EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, EN61547, Light industry level, criteria A
MTBF 621.4Khrs min. MIL-HDBK-217F (25°C)
Dimensions 145 x 47 x 30mm
  • CE